Diagram of decreasing apertures
, that is, increasing f-numbers, in one-stop increments; each aperture has half the light-gathering area of the previous one.
The f-number is the reciprocal
of the relative aperture
(the aperture diameter divided by focal length).
The f-number N is given by:
where is the focal length
is the diameter of the entrance pupil (effective aperture
). It is customary to write f-numbers preceded by f
/, which forms a mathematical expression of the entrance pupil diameter in terms of f
For example, if a lens'
focal length were 10 mm and its entrance pupil diameter were 5 mm, the f-number would be 2. This would be expressed as "f
/2" in a lens system. The aperture diameter would be equal to
Most lenses have an adjustable diaphragm
, which changes the size of the aperture stop
and thus the entrance pupil size. This allows the practitioner to vary the f-number, according to needs. It should be appreciated that the entrance pupil diameter is not necessarily equal to the aperture stop diameter, because of the magnifying effect of lens elements in front of the aperture.
Ignoring differences in light transmission efficiency, a lens with a greater f-number projects darker images. The brightness of the projected image (illuminance
) relative to the brightness of the scene in the lens's field of view (luminance
) decreases with the square of the f-number. A 100 mm focal length f
/4 lens has an entrance pupil diameter of 25 mm. A 100 mm focal length f
/2 lens has an entrance pupil diameter of 50 mm. Since the area varies as the square of the pupil diameter,
the amount of light admitted by the f
/2 lens is four times that of the f
/4 lens. To obtain the same photographic exposure
, the exposure time must be reduced by a factor of four.
A 200 mm focal length f/4 lens has an entrance pupil diameter of 50 mm. The 200 mm lens's entrance pupil has four times the area of the 100 mm f/4 lens's entrance pupil, and thus collects four times as much light from each object in the lens's field of view. But compared to the 100 mm lens, the 200 mm lens projects an image of each object twice as high and twice as wide, covering four times the area, and so both lenses produce the same illuminance at the focal plane when imaging a scene of a given luminance.
is an f-number adjusted to account for light transmission efficiency.
Stops, f-stop conventions, and exposure
A Canon 7
mounted with a 50 mm lens capable of f
A 35 mm lens set to f/11, as indicated by the white dot above the f-stop scale on the aperture ring. This lens has an aperture range of f/2.0 to f/22.
The word stop
is sometimes confusing due to its multiple meanings. A stop can be a physical object: an opaque part of an optical system that blocks certain rays. The aperture stop
is the aperture setting that limits the brightness of the image by restricting the input pupil size, while a field stop
is a stop intended to cut out light that would be outside the desired field of view and might cause flare or other problems if not stopped.
In photography, stops are also a unit
used to quantify ratios of light or exposure, with each added stop meaning a factor of two, and each subtracted stop meaning a factor of one-half. The one-stop unit is also known as the EV (exposure value
) unit. On a camera, the aperture setting is traditionally adjusted in discrete steps, known as f-stops
. Each "stop
" is marked with its corresponding f-number, and represents a halving of the light intensity from the previous stop. This corresponds to a decrease of the pupil and aperture diameters by a factor of
or about 0.7071, and hence a halving of the area of the pupil.
Most modern lenses use a standard f-stop scale, which is an approximately geometric sequence
of numbers that corresponds to the sequence of the powers
of the square root of 2
/128, etc. Each element in the sequence is one stop lower than the element to its left, and one stop higher than the element to its right. The values of the ratios are rounded off to these particular conventional numbers, to make them easier to remember and write down. The sequence above is obtained by approximating the following exact geometric sequence:
In the same way as one f-stop corresponds to a factor of two in light intensity, shutter speeds
are arranged so that each setting differs in duration by a factor of approximately two from its neighbour. Opening up a lens by one stop allows twice as much light to fall on the film in a given period of time. Therefore, to have the same exposure at this larger aperture as at the previous aperture, the shutter would be opened for half as long (i.e., twice the speed). The film will respond equally to these equal amounts of light, since it has the property of reciprocity
. This is less true for extremely long or short exposures, where we have reciprocity failure
. Aperture, shutter speed, and film sensitivity are linked: for constant scene brightness, doubling the aperture area (one stop), halving the shutter speed (doubling the time open), or using a film twice as sensitive, has the same effect on the exposed image. For all practical purposes extreme accuracy is not required (mechanical shutter speeds were notoriously inaccurate as wear and lubrication varied, with no effect on exposure). It is not significant that aperture areas and shutter speeds do not vary by a factor of precisely two.
Photographers sometimes express other exposure
ratios in terms of 'stops'. Ignoring the f-number markings, the f-stops make a logarithmic scale
of exposure intensity. Given this interpretation, one can then think of taking a half-step along this scale, to make an exposure difference of "half a stop".
Computer simulation showing the effects of changing a camera's aperture in half-stops (at left) and from zero to infinity (at right)
Most twentieth-century cameras had a continuously variable aperture, using an iris diaphragm
, with each full stop marked. Click-stopped aperture came into common use in the 1960s; the aperture scale usually had a click stop at every whole and half stop.
On modern cameras, especially when aperture is set on the camera body, f-number is often divided more finely than steps of one stop. Steps of one-third stop (1
EV) are the most common, since this matches the ISO system of film speeds
. Half-stop steps are used on some cameras. Usually the full stops are marked, and the intermediate positions are clicked. As an example, the aperture that is one-third stop smaller than f
/2.8 is f
/3.2, two-thirds smaller is f
/3.5, and one whole stop smaller is f
/4. The next few f-stops in this sequence are:
f/4.5, f/5, f/5.6, f/6.3, f/7.1, f/8, etc.
To calculate the steps in a full stop (1 EV) one could use
20×0.5, 21×0.5, 22×0.5, 23×0.5, 24×0.5 etc.
The steps in a half stop (1⁄2 EV) series would be
20/2×0.5, 21/2×0.5, 22/2×0.5, 23/2×0.5, 24/2×0.5 etc.
The steps in a third stop (1⁄3 EV) series would be
20/3×0.5, 21/3×0.5, 22/3×0.5, 23/3×0.5, 24/3×0.5 etc.
As in the earlier DIN and ASA film-speed standards, the ISO speed is defined only in one-third stop increments, and shutter speeds of digital cameras are commonly on the same scale in reciprocal seconds. A portion of the ISO range is the sequence
... 16/13°, 20/14°, 25/15°, 32/16°, 40/17°, 50/18°, 64/19°, 80/20°, 100/21°, 125/22°...
while shutter speeds in reciprocal seconds have a few conventional differences in their numbers (1⁄15, 1⁄30, and 1⁄60 second instead of 1⁄16, 1⁄32, and 1⁄64).
In practice the maximum aperture of a lens is often not an integral
power of √2
to the power of a whole number), in which case it is usually a half or third stop above or below an integral power of √2
Modern electronically controlled interchangeable lenses, such as those used for SLR cameras, have f-stops specified internally in 1⁄8-stop increments, so the cameras' 1⁄3-stop settings are approximated by the nearest 1⁄8-stop setting in the lens.
Standard full-stop f-number scale
Conventional and calculated f-numbers, full-stop series:
Typical one-half-stop f-number scale
Typical one-third-stop f-number scale
Sometimes the same number is included on several scales; for example, an aperture of f
/1.2 may be used in either a half-stop
or a one-third-stop system;
/1.3 and f
/3.2 and other differences are used for the one-third stop scale.
Typical one-quarter-stop f-number scale
(for transmission stops, by convention written with capital letter T) is an f-number adjusted to account for light transmission efficiency (transmittance
). A lens with a T-stop of N
projects an image of the same brightness as an ideal lens with 100% transmittance and an f-number of N
. A particular lens' T-stop, T
, is given by dividing the f-number by the square root of the transmittance of that lens:
For example, an f/2.0 lens with transmittance of 75% has a T-stop of 2.3:
Since real lenses have transmittances of less than 100%, a lens's T-stop number is always greater than its f-number.
With 8% loss per air-glass surface on lenses without coating, multicoating
of lenses is the key in lens design to decrease transmittance losses of lenses. Some reviews of lenses do measure the t-stop or transmission rate in their benchmarks.
T-stops are sometimes used instead of f-numbers to more accurately determine exposure, particularly when using external light meters
Lens transmittances of 60%–95% are typical.
T-stops are often used in cinematography, where many images are seen in rapid succession and even small changes in exposure will be noticeable. Cinema camera lenses are typically calibrated in T-stops instead of f-numbers.
In still photography, without the need for rigorous consistency of all lenses and cameras used, slight differences in exposure are less important; however, T-stops are still used in some kinds of special-purpose lenses such as Smooth Trans Focus
lenses by Minolta
Sunny 16 rule
An example of the use of f-numbers in photography is the sunny 16 rule
: an approximately correct exposure will be obtained on a sunny day by using an aperture of f
/16 and the shutter speed closest to the reciprocal of the ISO speed of the film; for example, using ISO 200 film, an aperture of f
/16 and a shutter speed of 1
second. The f-number may then be adjusted downwards for situations with lower light. Selecting a lower f-number is "opening up" the lens. Selecting a higher f-number is "closing" or "stopping down" the lens.
Effects on image sharpness
Comparison of f/32 (top-left corner) and f/5 (bottom-right corner)
Shallow focus with a wide open lens
Depth of field
increases with f-number, as illustrated in the image here. This means that photographs taken with a low f-number (large aperture) will tend to have subjects at one distance in focus, with the rest of the image (nearer and farther elements) out of focus. This is frequently used for nature photography
because background blur (the aesthetic quality known as 'bokeh
') can be aesthetically pleasing and puts the viewer's focus on the main subject in the foreground. The depth of field
of an image produced at a given f-number is dependent on other parameters as well, including the focal length
, the subject distance, and the format
of the film or sensor used to capture the image. Depth of field can be described as depending on just angle of view, subject distance, and entrance pupil
diameter (as in von Rohr's method
). As a result, smaller formats will have a deeper field than larger formats at the same f-number for the same distance of focus and same angle of view since a smaller format requires a shorter focal length (wider angle lens) to produce the same angle of view, and depth of field increases with shorter focal lengths. Therefore, reduced–depth-of-field effects will require smaller f-numbers (and thus potentially more difficult or complex optics) when using small-format cameras than when using larger-format cameras.
Beyond focus, image sharpness is related to f-number through two different optical effects: aberration
, due to imperfect lens design, and diffraction
which is due to the wave nature of light.
The blur-optimal f-stop varies with the lens design. For modern standard lenses having 6 or 7 elements, the sharpest
image is often obtained around f
/8, while for older standard lenses having only 4 elements (Tessar formula
) stopping to f
/11 will give the sharpest image
. The larger number of elements in modern lenses allow the designer to compensate for aberrations, allowing the lens to give better pictures at lower f-numbers. At small apertures, depth of field and aberrations are improved, but diffraction
creates more spreading of the light, causing blur.
Light falloff is also sensitive to f-stop. Many wide-angle lenses will show a significant light falloff (vignetting
) at the edges for large apertures.
have a saying, "f/8 and be there
", meaning that being on the scene is more important than worrying about technical details. Practically, f
/8 (in 35 mm and larger formats) allows adequate depth of field and sufficient lens speed for a decent base exposure in most daylight situations.
Computing the f-number of the human eye
involves computing the physical aperture and focal length of the eye. The pupil can be as large as 6–7 mm wide open, which translates into the maximal physical aperture.
The f-number of the human eye varies from about f
/8.3 in a very brightly lit place to about f
/2.1 in the dark.
Computing the focal length requires that the light-refracting properties of the liquids in the eye be taken into account. Treating the eye as an ordinary air-filled camera and lens results in a different focal length, thus yielding an incorrect f-number.
Toxic substances and poisons
) can significantly reduce the range of aperture. Pharmaceutical products such as eye drops may also cause similar side-effects. Tropicamide
are used in medicine as mydriatics to dilate pupils for retinal and lens examination. These medications take effect in about 30–45 minutes after instillation and last for about 8 hours. Atropine is also used in such a way but its effects can last up to 2 weeks, along with the mydriatic effect; it produces cycloplegia
(a condition in which the crystalline lens of the eye cannot accommodate to focus near objects). This effect goes away after 8 hours. Other medications offer the contrary effect. Pilocarpine is a miotic (induces miosis); it can make a pupil as small as 1 mm in diameter depending on the person and their ocular characteristics. Such drops are used in certain glaucoma
patients to prevent acute glaucoma attacks.
Focal ratio in telescopes
In astronomy, the f-number is commonly referred to as the focal ratio
) notated as
. It is still defined as the focal length
of an objective
divided by its diameter
or by the diameter of an aperture
stop in the system:
Even though the principles of focal ratio are always the same, the application to which the principle is put can differ. In photography
the focal ratio varies the focal-plane illuminance (or optical power per unit area in the image) and is used to control variables such as depth of field
. When using an optical telescope
in astronomy, there is no depth of field issue, and the brightness of stellar point sources in terms of total optical power (not divided by area) is a function of absolute aperture area only, independent of focal length. The focal length controls the field of view
of the instrument and the scale of the image that is presented at the focal plane to an eyepiece
, film plate, or CCD
For example, the SOAR
4-meter telescope has a small field of view (~f
/16) which is useful for stellar studies. The LSST
8.4 m telescope, which will cover the entire sky every three days, has a very large field of view. Its short 10.3 m focal length (f
/1.2) is made possible by an error correction system which includes secondary and tertiary mirrors, a three element refractive system and active mounting and optics.
τ is the transmission coefficient of the lens, and the units are in sr−1.
The f-number accurately describes the light-gathering ability of a lens only for objects an infinite distance away.
This limitation is typically ignored in photography, where f-number is often used regardless of the distance to the object. In optical design
, an alternative is often needed for systems where the object is not far from the lens. In these cases the working f-number
is used. The working f-number Nw
is given by:
is the uncorrected f-number, NAi
is the image-space numerical aperture
of the lens,
is the absolute value
of the lens's magnification
for an object a particular distance away, and P
is the pupil magnification
. Since the pupil magnification is seldom known it is often assumed to be 1, which is the correct value for all symmetric lenses.
In photography this means that as one focuses closer, the lens' effective aperture becomes smaller, making the exposure darker. The working f-number is often described in photography as the f-number corrected for lens extensions by a bellows factor
. This is of particular importance in macro photography
The system of f-numbers for specifying relative apertures evolved in the late nineteenth century, in competition with several other systems of aperture notation.
Origins of relative aperture
In 1867, Sutton and Dawson defined "apertal ratio" as essentially the reciprocal of the modern f-number. In the following quote, an "apertal ratio" of "1⁄24" is calculated as the ratio of 6 inches (150 mm) to 1⁄4 inch (6.4 mm), corresponding to an f/24 f-stop:
In every lens there is, corresponding to a given apertal ratio (that is, the ratio of the diameter of the stop to the focal length), a certain distance of a near object from it, between which and infinity all objects are in equally good focus. For instance, in a single view lens of 6-inch focus, with a 1
in. stop (apertal ratio one-twenty-fourth), all objects situated at distances lying between 20 feet from the lens and an infinite distance from it (a fixed star, for instance) are in equally good focus. Twenty feet is therefore called the 'focal range' of the lens when this stop is used. The focal range is consequently the distance of the nearest object, which will be in good focus when the ground glass is adjusted for an extremely distant object. In the same lens, the focal range will depend upon the size of the diaphragm used, while in different lenses having the same apertal ratio the focal ranges will be greater as the focal length of the lens is increased. The terms 'apertal ratio' and 'focal range' have not come into general use, but it is very desirable that they should, in order to prevent ambiguity and circumlocution when treating of the properties of photographic lenses.
of a lens depends upon the relation or ratio of the aperture to the equivalent focus. To ascertain this, divide the equivalent focus
by the diameter of the actual working aperture
of the lens in question; and note down the quotient as the denominator with 1, or unity, for the numerator. Thus to find the ratio of a lens of 2 inches diameter and 6 inches focus, divide the focus by the aperture, or 6 divided by 2 equals 3; i.e., 1
is the intensity ratio.
Although he did not yet have access to Ernst Abbe
's theory of stops and pupils,
which was made widely available by Siegfried Czapski
Dallmeyer knew that his working aperture
was not the same as the physical diameter of the aperture stop:
It must be observed, however, that in order to find the real intensity ratio
, the diameter of the actual working aperture must be ascertained. This is easily accomplished in the case of single lenses, or for double combination lenses used with the full opening, these merely requiring the application of a pair of compasses or rule; but when double or triple-combination lenses are used, with stops inserted between
the combinations, it is somewhat more troublesome; for it is obvious that in this case the diameter of the stop employed is not the measure of the actual pencil of light transmitted by the front combination. To ascertain this, focus for a distant object, remove the focusing screen and replace it by the collodion slide, having previously inserted a piece of cardboard in place of the prepared plate. Make a small round hole in the centre of the cardboard with a piercer, and now remove to a darkened room; apply a candle close to the hole, and observe the illuminated patch visible upon the front combination; the diameter of this circle, carefully measured, is the actual working aperture of the lens in question for the particular stop employed.
This point is further emphasized by Czapski in 1893.
According to an English review of his book, in 1894, "The necessity of clearly distinguishing between effective aperture and diameter of physical stop is strongly insisted upon."
Aperture numbering systems
A 1922 Kodak with aperture marked in U.S. stops. An f-number conversion chart has been added by the user.
At the same time, there were a number of aperture numbering systems designed with the goal of making exposure times vary in direct or inverse proportion with the aperture, rather than with the square of the f-number or inverse square of the apertal ratio or intensity ratio. But these systems all involved some arbitrary constant, as opposed to the simple ratio of focal length and diameter.
For example, the Uniform System
(U.S.) of apertures was adopted as a standard by the Photographic Society of Great Britain
in the 1880s. Bothamley in 1891 said "The stops of all the best makers are now arranged according to this system."
U.S. 16 is the same aperture as f
/16, but apertures that are larger or smaller by a full stop use doubling or halving of the U.S. number, for example f
/11 is U.S. 8 and f
/8 is U.S. 4. The exposure time required is directly proportional to the U.S. number. Eastman Kodak
used U.S. stops on many of their cameras at least in the 1920s.
By 1895, Hodges contradicts Bothamley, saying that the f-number system has taken over: "This is called the f
system, and the diaphragms of all modern lenses of good construction are so marked."
Here is the situation as seen in 1899:
Piper in 1901
discusses five different systems of aperture marking: the old and new Zeiss
systems based on actual intensity (proportional to reciprocal square of the f-number); and the U.S., C.I., and Dallmeyer systems based on exposure (proportional to square of the f-number). He calls the f-number the "ratio number," "aperture ratio number," and "ratio aperture." He calls expressions like f
/8 the "fractional diameter" of the aperture, even though it is literally equal to the "absolute diameter" which he distinguishes as a different term. He also sometimes uses expressions like "an aperture of f 8" without the division indicated by the slash.
Beck and Andrews in 1902 talk about the Royal Photographic Society standard of f
The R.P.S. had changed their name and moved off of the U.S. system some time between 1895 and 1902.
camera front view. This is one of the few cameras that actually says "F-NUMBER" on it.
From the top, the Yashica-D's aperture setting window uses the "f:" notation. The aperture is continuously variable with no "stops".
By 1920, the term f-number
appeared in books both as F number
. In modern publications, the forms f-number
and f number
are more common, though the earlier forms, as well as F-number
are still found in a few books; not uncommonly, the initial lower-case f
is set in a hooked italic form: f
, or f
Notations for f-numbers were also quite variable in the early part of the twentieth century. They were sometimes written with a capital F,
sometimes with a dot (period) instead of a slash,
and sometimes set as a vertical fraction.
The 1961 ASA
standard PH2.12-1961 American Standard General-Purpose Photographic Exposure Meters (Photoelectric Type)
specifies that "The symbol for relative apertures shall be f/
: followed by the effective f
-number." They show the hooked italic f
not only in the symbol, but also in the term f-number
, which today is more commonly set in an ordinary non-italic face.
- ^ a b Smith, Warren Modern Optical Engineering, 4th Ed., 2007 McGraw-Hill Professional, p. 183.
- ^ Hecht, Eugene (1987). Optics (2nd ed.). Addison Wesley. p. 152. ISBN 0-201-11609-X.
- ^ Greivenkamp, John E. (2004). Field Guide to Geometrical Optics. SPIE Field Guides vol. FG01. Bellingham, Wash: SPIE. p. 29. ISBN 9780819452948. OCLC 53896720.
- ^ Smith, Warren Modern Lens Design 2005 McGraw-Hill.
- ^ ISO, Photography—Apertures and related properties pertaining to photographic lenses—Designations and measurements, ISO 517:2008
- ^ See Area of a circle.
- ^ Harry C. Box (2003). Set lighting technician's handbook: film lighting equipment, practice, and electrical distribution (3rd ed.). Focal Press. ISBN 978-0-240-80495-8.
- ^ Paul Kay (2003). Underwater photography. Guild of Master Craftsman. ISBN 978-1-86108-322-7.
- ^ David W. Samuelson (1998). Manual for cinematographers (2nd ed.). Focal Press. ISBN 978-0-240-51480-2.
- ^ Transmission, light transmission, DxOMark
- ^ Sigma 85mm F1.4 Art lens review: New benchmark, DxOMark
- ^ Colour rendering in binoculars and lenses - Colours and transmission, LensTip.com
- ^ a b "Kodak Motion Picture Camera Films". Eastman Kodak. November 2000. Archived from the original on 2002-10-02. Retrieved 2007-09-02.
- ^ Marianne Oelund, "Lens T-stops", dpreview.com, 2009
- ^ Michael John Langford (2000). Basic Photography. Focal Press. ISBN 0-240-51592-7.
- ^ Levy, Michael (2001). Selecting and Using Classic Cameras: A User's Guide to Evaluating Features, Condition & Usability of Classic Cameras. Amherst Media, Inc. p. 163. ISBN 978-1-58428-054-5.
- ^ Hecht, Eugene (1987). Optics (2nd ed.). Addison Wesley. ISBN 0-201-11609-X. Sect. 5.7.1
- ^ Charles F. Claver; et al. (2007-03-19). "LSST Reference Design" (PDF). LSST Corporation: 45–50. Archived from the original (PDF) on 2009-03-06. Retrieved 2011-01-10.
- ^ Driggers, Ronald G. (2003). Encyclopedia of Optical Engineering: Pho-Z, pages 2049-3050. CRC Press. ISBN 978-0-8247-4252-2. Retrieved 2020-06-18.
- ^ a b Greivenkamp, John E. (2004). Field Guide to Geometrical Optics. SPIE Field Guides vol. FG01. SPIE. ISBN 0-8194-5294-7. p. 29.
- ^ Thomas Sutton and George Dawson, A Dictionary of Photography, London: Sampson Low, Son & Marston, 1867, (p. 122).
- ^ a b John Henry Dallmeyer, Photographic Lenses: On Their Choice and Use – Special Edition Edited for American Photographers, pamphlet, 1874.
- ^ Southall, James Powell Cocke (1910). "The principles and methods of geometrical optics: Especially as applied to the theory of optical instruments". Macmillan: 537. theory-of-stops.
- ^ a b Siegfried Czapski, Theorie der optischen Instrumente, nach Abbe, Breslau: Trewendt, 1893.
- ^ Henry Crew, "Theory of Optical Instruments by Dr. Czapski," in Astronomy and Astro-physics XIII pp. 241–243, 1894.
- ^ Thomas R. Dallmeyer, Telephotography: An elementary treatise on the construction and application of the telephotographic lens, London: Heinemann, 1899.
- ^ C. H. Bothamley, Ilford Manual of Photography, London: Britannia Works Co. Ltd., 1891.
- ^ John A. Hodges, Photographic Lenses: How to Choose, and How to Use, Bradford: Percy Lund & Co., 1895.
- ^ C. Welborne Piper, A First Book of the Lens: An Elementary Treatise on the Action and Use of the Photographic Lens, London: Hazell, Watson, and Viney, Ltd., 1901.
- ^ Conrad Beck and Herbert Andrews, Photographic Lenses: A Simple Treatise, second edition, London: R. & J. Beck Ltd., c. 1902.
- ^ Google search
- ^ Ives, Herbert Eugene (1920). Airplane Photography (Google). Philadelphia: J. B. Lippincott. p. 61. ISBN 9780598722225. Retrieved 2007-03-12.
- ^ Mees, Charles Edward Kenneth (1920). The Fundamentals of Photography. Eastman Kodak. p. 28. Retrieved 2007-03-12.
- ^ Derr, Louis (1906). Photography for Students of Physics and Chemistry (Google). London: Macmillan. p. 83. Retrieved 2007-03-12.
Wikimedia Commons has media related to F-number
Last edited on 7 June 2021, at 12:55
Content is available under CC BY-SA 3.0
unless otherwise noted.